USB Hub Design Walkthrough - Phil's Lab #86

How To Learn PCB Design (My Thoughts, Journey, and Resources) - Phil's Lab #87

Recommendations on how to approach learning PCB and hardware design, including my journey, thoughts on university courses, IPC CID, ECAD tools, and resource tips. [SUPPORT] Free trial of Altium Designer: https://www.altium.com/yt/philslab Patreon: ...

By Phil’s Lab

Duration: 18:48

USB High Speed Routing (ULPI, Delay Tuning) - Phil's Lab #67

Routing tips for USB High-Speed (HS) ULPI interfaces. Including guidlines on timing requirements, controlled impedance, package/via/trace delays, Altium tips, and more. Mixed-signal hardware design course: https://phils-lab-shop.fedevel.education [...

By Phil’s Lab

Duration: 15:30

USB Headphone Amplifier Design Walkthrough - Phil's Lab #101

USB-C low-noise, low-distortion headphone amplifier design walkthrough. Update video from previous version, going through design considerations, schematics, and PCB design. PCBs by PCBWay www.pcbway.com [SUPPORT] Free trial of Altium Designer: https...

By Phil’s Lab

Duration: 33:55

USB Hub Design - Part 1/x - Overview and Theory

USB Hub Design - Part 1/x - Overview and Theory This is the first part of a new extended series going over the design of a complex USB hub. Your feedback decides the route that this project goes! Please share thoughts and comments in the comment sec...

By MicroType Engineering

Duration: 22:19

USB Hub Design - Part 3/x - Initial Schematic Design

USB Hub Design - Part 3/x - Initial Schematic Design This is the third part of an extended series going over the design of a complex USB hub. Your feedback decides the route that this project goes! Please share thoughts and comments in the comment s...

By MicroType Engineering

Duration: 23:04

Mini 6-Layer Mixed-Signal Hardware Design Walkthrough - Phil's Lab #78

Thanks to the new channel sponsor PCBWay! PCBs manufactured and assembled by PCBWay at https://www.pcbway.com Walkthrough of double-sided assembly, 6-layer mixed-signal hardware design (overview, schematic, and PCB) of a digital signal processing bo...

By Phil’s Lab

Duration: 26:25

KiCad 6 STM32 PCB Design Full Tutorial - Phil's Lab #65

Complete step-by-step PCB design process going through the schematic, layout, and routing of a 'black-pill' STM32-based PCB including USB in the *new* KiCAD 6. All the way from schematic creation, through to two-layer PCB layout and routing...

By Phil’s Lab

Duration: 100:05

KiCad STM32 + RF + USB Hardware Design - Phil's Lab #5

⏵Hardware and PCB design course: https://www.phils-lab.net/courses Overview of STM32, RF, and USB hardware design, schematic creation, and PCB layout and routing in KiCad using a real-world example project. (Timestamps in description) Various tip...

By Phil’s Lab

Duration: 44:01

STM32 PCB Design - Complete Walkthrough - Altium Designer & JLCPCB - Phil's Lab #41

Mixed-signal hardware design course: https://phils-lab-shop.fedevel.education Entire step-by-step PCB design process going through the schematic, layout, and routing of a 'barebones' STM32F4-based PCB including USB, a sensor, GPIO header, a...

By Мастер JavaScript

Duration: 168:30

Aesthetic PCB Design Tips - Phil's Lab #84

Tips for creating aestheticly-pleasing PCB designs, which in turn also benefit functionality, manufacturability, and more. From grid sizes, placement, silkscreen, to edge shielding, and more - make sure to incorporate these tips into your next PCB de...

By Phil’s Lab

Duration: 17:56

STM32 Programming via USB (DFU) - Phil's Lab #72

How to flash firmware via USB to STM32 devices via DFU (device firmware upgrade) and STM32 Cube Programmer. This way you do not need an ST-Link or similar programmer to flash firmware - however, you cannot set breakpoints, debug, and so on. Note: thi...

By Phil’s Lab

Duration: 5:08

№ 10 Как отремонтировать USB Hub 3.0

В этом выпуске я покажу как соединить разорванные провода USB хаба 3.0. Группа Вконтакте: https://vk.com/public123108254 Я Вконтакте: https://vk.com/id154049606 Ур�...

By Off-Road Эксперименты

Duration: 4:32

Design Review - Schematic & PCB - Phil's Lab #70

Second design review of series. Examining schematic and PCB design of a wireless keyboard adapter made using KiCad. Common errors, best practices, routing techniques, and so on discussed in brief. Thanks to Andrew for sending this one in! Send your d...

By Phil’s Lab

Duration: 16:12

Making Enclosure Panels Using PCBs - Phil's Lab #102

How to design PCBs to make low-cost, front- and rear-panels for 'standardised' enclosures. Including sizing, hole positioning, manufacturing details and options, and assembly example. [SUPPORT] Free trial of Altium Designer: https://www.al...

By Phil’s Lab

Duration: 26:14

Critiquing My Own PCB Designs - Phil's Lab #43

My first PCB design was in 2019 - let's look back and see how bad these were and how I've improved over the last few years! Featuring KiCad 6.0 and Altium Designer. (Apologies for the less-than-optimal audio!) [SUPPORT] Free trial of Altiu...

By Phil’s Lab

Duration: 24:53

Differential Pairs - PCB Design Basics - Phil's Lab #83

Differential pair PCB design basics, covering differential signalling benefits, references, impedance control, inter- and intra-pair matching, and termination. ***Advanced Hardware Design Course Survey*** https://forms.gle/X4jwvtZeJ1jTXh7r9 Rick Ha...

By Phil’s Lab

Duration: 21:52

ESC Hardware Design - Phil's Lab #66

How to design our own simple ESC (electronic speed controller) for control of brushless DC motors (BLDCs), including tips on ESC structure, power section, current and voltage feedback, microcontroller pin-out, USB HS ULPI, and more. Mixed-signal har...

By Phil’s Lab

Duration: 18:39

Экстрасенсы. Реванш, 2 сезон, 2 выпуск

Современный обезболивающий крем Артраксикам с тройным действием: ускоренное проникновение в очаг боли, обезболивающее и противовоспал...

By Телеканал ТНТ

Duration: 114:43

Дуния: Погружение в новый мир, 8 выпуск

By Корейские шоу

Duration: 63:08

ВСЕ О КИСТЯХ для МАКИЯЖА

ВСЕ О КИСТЯХ для МАКИЯЖА! Приятного просмотра запретограм - cosmos_dg реклама - offer@peaches.studio телега - https://t.me/graphdg VK - https://vk.com/id156990967

By Дарья Граф

Duration: 28:25